View AWT6310R_645794.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AWT6310R
Dual-band CDMA/PCS 3.4 V/28 dBm Linear Power Amplifier Module
PRELIMINARY DATA SHEET - Rev 1.1
FEATURES
* * * * * * * * * Single Mode Operation: POUT +28 dBm High Efficiency: 54 % AMPS, 39 % CDMA Low Quiescent Current: 50 mA 25 % Package Size Reduction Common VMODE Control Line Simplified VCC Bus PCB routing Reduced External Component Count Low Profile Surface Mount Package: 1.1 mm RoHS Compliant Package, 250 oC MSL-3
AW T
631
0R
APPLICATIONS
* Dual-band Cellular/PCS CDMA Wireless Handsets
M23 Package 12 Pin 3 mm x 5 mm x 1 mm Surface Mount Module PRODUCT DESCRIPTION
The AWT6310R meets the increasing demands for higher levels of integration in dual-band CDMA/PCS 1X handsets, while reducing board area requirements by 25 %. The package pinout was chosen to enable handset manufacturers to easily route VCC to both power amplifiers and simplify control with a common VMODE pin. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability, and ruggedness. Selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, serve to increase handset talk and standby time. The self contained 3 mm x 5 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency and linearity in a 50 system.
GND at slug (pad)
VREF_CELL
1 Bias Control 12 GND
RFIN_CELL
2
11 RFOUT_CELL
VMODE
3
10 VCC2 A
VCC1 4
9
VCC2
RFIN_PCS 5
Bias Control
8
GND
VREF_PCS 6
7
RFOUT_PCS
GND
Figure 1: Block Diagram
05/2006
AWT6310R
GND VREF_CELL RFIN_CELL VMODE VCC1 RFIN_PCS VREF_PCS 1 2 3 4 5 6 GND
Figure 2: Pinout
12 11 10 9 8 7
GND RFOUT_CELL VCC2A VCC2 GND RFOUT_PCS
Table 1: Pin Description
PIN 1 2 3 4 5 6 7 8 9 10 11 12
NAME VREF_CELL RFIN_CELL VMODE V CC1 RFIN_PCS VREF_PCS
DESCRIPTION Reference Voltage for Cell Band RF Input for Cell Band Mode Control Voltage Supply Voltage RF Input for PCS Band Reference Voltage for PCS Band
RFOUT_PCS RF Output for PCS Band GND V CC2 V C C 2A Ground Supply Voltage Supply Voltage
RFOUT_CELL RF Output for Cell Band GND Ground
2
PRELIMINARY DATA SHEET - Rev 1.1 05/2006
AWT6310R
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings PAR AME T E R Supply Voltage (VCC ) Wi th RF Dri ve DC Only Mode Control Voltage (VMODE) Reference Voltage (VREF) RF Input Power (PIN) Storage Temperature (TSTG) MIN 0 0 0 0 -40 M AX +5 +8 +3.5 +3.5 +10 +150 U N IT
V V V dBm C
Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability.
Table 3: Operating Ranges
PARAMETER Operating Frequency (f) Supply Voltage (VCC) Reference Voltage (VREF) Mode Control Voltage (VMODE) RF Output Power (POUT) Case Temperature (TC)
MIN 824 1850 +3.2 +2.75 0 +2.5 0 30.5(1) 27.5(1) -30
TYP +3.4 +2.85 +2.85 31.0 28.0 -
MAX 849 1910 +4.2 +3.1 +0.5 +3.1 +0.5 +85
UNIT MHz V V V dB m C
COMMENTS Cellular PC S
PA "on" PA "shut down" Low Bias Mode High Bias Mode AMPS CDMA
The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at VCC = +3.2 V, POUT is derated by 0.5 dB.
PRELIMINARY DATA SHEET - Rev 1.1 05/2006
3
AWT6310R Table 4: Electrical Specifications - AMPS Operation (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, VMODE = 2.85 V, POUT = +31 dBm, 50 system)
PARAMETER Gain Gain Variation Power-Added Efficiency (1) Quiescent Current (Icq) Reference Current Leakage Current Noise in Receive Band Harmonics 2fo 3fo, 4fo Input Impedance MIN 24 50 TYP 26 0.4 54 50 1.5 <1 -134 -46 -50 MAX 29 1.0 70 3 5 -132 -30 -30 2:1 UNIT dB dB % mA mA A dBm/Hz Low B i as through VREF pin VCC = +4.2 V, VREF = 0 V, VMODE = 0 V 869 MHz to 894 MHz COMMENTS
dB c
VSWR POUT < +31 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions Applies over all operating conditions
Spurious Output Level (all spurious outputs)
-
-
-65
dB c
Load mismatch stress with no permanent degradation or failure
Notes: (1) PAE limit applies at 824 MHz.
10:1
-
-
VSWR
4
PRELIMINARY DATA SHEET - Rev 1.1 05/2006
AWT6310R Table 5: Electrical Specifications - Cellular CDMA Operation (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, 50 system)
PARAMETER MIN 25 24 24 37 37 8 TYP 27.0 26.5 25.5 -50 -51 -50 -62 -60 -66 39 40 9 50 1.5 0.6 <1 -133 -35 -50 MAX 29 29 28 -47 -47 -47 -57 -56 -57 70 3 1.0 5 -131 -30 -30 2:1 UNIT COMMENTS POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V VMODE = +2.85 V, Low Bias through VREF pin through VMODE pin VCC = +4.2 V, VREF = 0 V, VMODE = 0 V 869 MHz to 894 MHz
Gain Adjacent Channel Power at 885 kHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kH Adjacent Channel Power at 1.98 MHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz Power-Added Efficiency (1)
dB
dB c
dB c
%
Quiescent Current (Icq) Reference Current Mode Control Current Leakage Current Noise in Receive Band Harmonics 2fo 3fo, 4fo Input Impedance
mA mA mA A dBm/Hz
dB c
VSWR POUT < +28 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions Applies over all operating conditions
Spurious Output Level (all spurious outputs)
-
-
-65
dB c
Load mismatch stress with no permanent degradation or failure
10:1
-
-
VSWR
Notes: (1) PAE and ACP limit applies at 836.5 MHz.
PRELIMINARY DATA SHEET - Rev 1.1 05/2006
5
AWT6310R Table 6: PCS Electrical Specifications (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, 50 system)
PARAMETER
MIN 25 24 23 37 37 8 -
TYP 26.5 26.0 25.0 -50 -51 -53 -61 -60 -67 39 40 9 48 2.3 0.6 <1 -133 -46 -55 -
MAX 29 28 28 -47 -47 -47 -57 -56 -57 62 4 1.0 5 -131 -30 -30 2:1
UNIT
COMMENTS POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V VMODE = +2.85 V through VREF pin, PA "on" through VMODE pin, VMODE = +2.85 V VCC = +4.2 V, VREF = 0 V, VMODE = 0 V
Gain Adjacent Channel Power at +1.25 MHz offset Primary Channel BW - 1.23 MHz Adjacent Channel BW = 30 kHz Adjacent Channel Power at +2.25 MHz offset Primary Channel BW - 1.23 MHz Adjacent Channel BW = 30 kHz Power-Added Efficiency Quiescent Current (Icq) Reference Current Mode Control Current Leakage Current Noise in Receive Band Harmonics 2fo 3fo, 4fo Input Impedance Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure
dB
dB c
dB c
% mA mA mA A
dBm/Hz 1930 MHz to 1990 MHz
dB c VSWR POUT < +28 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all operating ranges Applies over full operating range
-
-
-65
dB c
8:1
-
-
VSWR
Notes: (1) ACPRs and efficiency limits at mid-band only.
6
PRELIMINARY DATA SHEET - Rev 1.1 05/2006
AWT6310R
APPLICATION INFORMATION
To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying a logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications.
Table 7: Bias Control
APPLICATION AMPS CDMA - low power CDMA - high power Shutdown POUT LE V E LS (all) <28 dBm >16 dBm BIAS MODE Low Low High Shutdown V R EF VMODE
+2.85 V +2.85 V +2.85 V +2.85 V +2.85 V 0V 0V 0V
GND at slug (pad)
VREF_CELL
0.01 F
1 Bias Control
12 GND
RFIN_CELL
68 pF
2
11
Note 1
3.9 nH
VMODE
3
10
1000 pF
VCC2
VCC1
2.2 F 1000 pF
4
9
TRL
2.2 F
RFIN_PCS
5 Bias Control
8
GND
68 pF
VREF_PCS
0.01 F
6
7
GND
Note: 1. 3.9 nH Inductor should be rated for >1 Amp.
Figure 3: Application Circuit
PRELIMINARY DATA SHEET - Rev 1.1 05/2006
7
AWT6310R
PACKAGE OUTLINE
Figure 4: Package Outline - 12 Pin 3 mm x 5 mm x 1 mm Surface Mount Module
1. ANADIGICS LOGO SIZE: 2. PART NUMBER:
NONE FOUR DIGIT NUMERICAL LLLLL = LOT NUMBER NN = WAFER I.D. LASER DOT BBBB CC = TH-for-THAILAND, TW-for-TAIWAN CC = PH-for-PHILIPPINES, CH-for-CHINA YY = YEAR, WW = WORK WEAK ARIAL 1.5-POINT LASER
6310R LLLLLNN BBBBCC YYWW
3. WAFER LOT NUMBER:
4. PIN 1 INDICATOR: 5. B.O.M. #: 6. COUNTRY CODE
7. YEAR & WORK WEEK 8. TYPE: SIZE: COLOR:
Figure 5: Branding Specification 8
PRELIMINARY DATA SHEET - Rev 1.1 05/2006
AWT6310R
NOTES
PRELIMINARY DATA SHEET - Rev 1.1 05/2006
9
AWT6310R
NOTES
10
PRELIMINARY DATA SHEET - Rev 1.1 05/2006
AWT6310R
NOTES
PRELIMINARY DATA SHEET - Rev 1.1 05/2006
11
AWT6310R
ORDERING INFORMATION
ORDER NUMBER AWT6310RM23Q7 TEMPERATURE RANGE -30 C to +85 C PACKAGE DESCRIPTION RoHS Compliant 12 Pin 3 mm x 5 mm x 1 mm Surface Mount Module COMPONENT PACKAGING
Tape and Reel, 2500 pieces per Reel
ANADIGICS, Inc.
141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders.
WARNING
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited.
12
PRELIMINARY DATA SHEET - Rev 1.1 05/2006

▲Up To Search▲

Price & Availability of AWT6310R

	To Download AWT6310R Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .